P0562

New Holland P0562 – DCU or ECM/PCM: Battery Voltage Evaluation - Below

Issue description

The system has detected that the battery voltage is below the lower threshold, typically dropping below 10 to 11.5 volts while the engine is running. This indicates a problem with the power supply or the battery itself, as the affected circuit is responsible for monitoring and evaluating the battery voltage. When the voltage falls below this critical level, it can lead to erratic behavior of electrical components, poor engine performance, and potential damage to sensitive electronics.

Applies to these machines

  • T4
  • T5
  • T6
  • T7
  • T8
  • Boomer
  • T7.210
  • T7.220
  • T7.230
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • T6000
  • 40 Series

Check the cause

  1. Visually inspect battery terminals for white or green corrosion buildup and ensure connections are clean and tight.

  2. Check main battery cables for signs of wear, corrosion, or damage.

  3. Inspect relevant electrical system fuses and the fusible link at the starter solenoid.

  4. Measure static battery voltage with the engine off (a healthy battery should read approximately 12.6 volts; below 12.4V indicates a weak charge).

  5. Perform a battery load test to ensure voltage does not drop below 9 volts under load.

  6. Measure charging system voltage with the engine running (should be 13.5 to 14.8 volts at the battery terminals).

  7. Check alternator output directly at the main output post to compare with battery voltage.

  8. Perform a voltage drop test on positive and negative cables with the engine running and electrical loads on (above 0.5V on positive or 0.2V on ground indicates excessive resistance).

  9. Inspect and clean all major ground connections (main battery ground to chassis, engine-to-chassis strap, and cab-to-chassis strap).

Repair steps

  1. Address Immediate Findings

    Begin by correcting any issues found during the diagnostic checks. Clean corroded battery terminals with a wire brush and baking soda solution, and tighten all connections.

  2. Charge or Replace the Battery

    If the battery failed a load test or is unable to hold a charge, replace it. A weak battery is a very common cause for this fault.

  3. Inspect and Repair Wiring

    If a voltage drop test revealed high resistance, trace the problematic cable (positive or negative) and inspect for corrosion, damage, or loose connections, particularly at junctions or connectors between the cab and chassis. Repair or replace the damaged section of the wiring harness.

  4. Check the Serpentine Belt

    Inspect the alternator's drive belt for proper tension, cracks, or glazing. A slipping belt will prevent the alternator from charging effectively.

  5. Replace the Alternator

    If the diagnostic tests confirm that the alternator is not producing the correct voltage (and the drive belt is in good condition), the alternator is likely faulty and should be replaced.

  6. Clear Fault Codes

    After completing repairs, use a diagnostic scanner to clear the P0562 fault code and any other related codes.

  7. Verify the Repair

    Run the tractor with electrical accessories on to ensure the voltage remains stable and the fault code does not reappear.

Parts you might need

(13)
  • SmartStart Premium Heavy-Duty Battery

    BNHD5W

    Fits various models including some T7 tractors

  • 120AH Battery

    Fits various models including T6000 and 40 Series

  • 170-180AH Battery

    Fits models like the T7.210

  • OEM alternatives: 87565015, 87667991. Fits T7.230, T7.245, T7.260

  • OEM alternative: 87708176. Fits T6 and T7 series

  • Fits T7.220 through T7.270 models

  • New Holland remanufactured option

  • Battery Cables and Terminals

    Replace as needed if corrosion is severe

  • Ground Straps

    Use good quality braided straps for engine-to-chassis and cab-to-chassis grounds

  • Battery

    F770DSW

    Conventional lead-acid type, 105 Ah, 800 CCA. Fits a wide range of tractors, including the T8.320 (which uses two 12-volt batteries).

  • AlternatorSBA185046320

    Replacement alternator for various New Holland tractors and skid steers.

  • Alternator92281C1GV

    Alternator listed for New Holland equipment.

  • Alternator82001260

    70-amp alternator for some Ford New Holland models.

Get help to fix this fault by requesting a quote

Browse other New Holland codes