Deutz-Fahr fault codes & repair guides
All 1,810 codes· 50 per page · page 16 of 37
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 1222 | — | Camshaft and Crankshaft Sensor Signal Not Available on CAN Bus | Full repair manual for code 1222 |
| 1223 | — | H-bridge driver and cable break in Actuator AGR valve and Throttle valve | Full repair manual for code 1223 |
| 1224 | — | Electrically Overloaded Actuator AGR Valve | Full repair manual for code 1224 |
| 1226 | — | AGR Valve or Throttle Valve Fault | Full repair manual for code 1226 |
| 1227 | — | AGRV Valve Issue | Full repair manual for code 1227 |
| 1228 | — | AGR Valve and Throttle Valve Fault with Ground Short Circuit | Full repair manual for code 1228 |
| 1229 | — | AGR Valve (2.9; 3.6) Throttle Valve (4.1; 6.1; 7.8); Short to Ground (A 67) | Full repair manual for code 1229 |
| 1230 | — | Actuator AGR Valve Throttle Valve Overload due to short circuit | Full repair manual for code 1230 |
| 1231 | — | Actuator AGR Valve (2.9; 3.6) Throttle Valve (4.1; 6.1; 7.8) Power Level Overtemperature due to excessive Storm | Full repair manual for code 1231 |
| 1231 | — | Cable Break or Short Circuit in Off-State (CAN Bus B) | Full repair manual for code 1231 |
| 1232 | — | Voltage Below Limit Related to Actuator AGR Valve and Throttle Valve | Full repair manual for code 1232 |
| 1235 | — | Cable Break or Short Circuit in Off-State (CAN Bus C) | Full repair manual for code 1235 |
| 1237 | — | Switch Hangs | Full repair manual for code 1237 |
| 1239 | — | Battery Short Circuit in Actuator Relay 6 | Full repair manual for code 1239 |
| 1241 | — | Short Circuit to Ground in Actuator Relay 6 | Full repair manual for code 1241 |
| 1241 | — | SCR Heater Relay Ground Short (Highside Control Side) | Full repair manual for code 1241 |
| 1242 | — | Short Circuit to Ground in Actuator Relay 6 | Full repair manual for code 1242 |
| 1247 | — | Air Pump and Air Line Blockage | Full repair manual for code 1247 |
| 1248 | — | Air Pump and CAN Communication Issue | Full repair manual for code 1248 |
| 1249 | — | Burner Control and Air Pump Electronics & Voltage Issue | Full repair manual for code 1249 |
| 1250 | — | Air Pump Internal Error | Full repair manual for code 1250 |
| 1252 | — | Air Pump - Incorrect Voltage | Full repair manual for code 1252 |
| 1254 | — | Air Pressure Glow Plug Flushing Line: Minimum Value Exceeded | Full repair manual for code 1254 |
| 1257 | — | HCI Dosing Valve (DV 1) Open Blocked | Full repair manual for code 1257 |
| 1258 | — | HFM Sensor Electrical Fault | Full repair manual for code 1258 |
| 1259 | — | Supplied air volume not plausible to pump speed | Full repair manual for code 1259 |
| 1261 | — | Voltage above limit air pump | Full repair manual for code 1261 |
| 1262 | — | Brenner Shut Off Valve is Closed and Blocked | Full repair manual for code 1262 |
| 1263 | — | Brenner fuel line after shut off valve leaking | Full repair manual for code 1263 |
| 1264 | — | Brenner Shut Off Valve: Open Blocked | Full repair manual for code 1264 |
| 1274 | — | Throttle Position 1 - Voltage Above Normal Value or Short Circuit to Plus | Full repair manual for code 1274 |
| 1275 | — | Throttle Pedal 1 Channel 2 - Voltage Above Normal Value or Short Circuit to Plus | Full repair manual for code 1275 |
| 1276 | — | Throttle Position 2 - Voltage Above Normal Value or Short Circuit to Plus | Full repair manual for code 1276 |
| 1277 | — | Throttle Pedal 2 Channel 2 - Voltage Above Normal Value or Short Circuit to Plus | Full repair manual for code 1277 |
| 1280 | — | Throttle Position 1 - Voltage Below Normal Value or Short Circuit to Ground | Full repair manual for code 1280 |
| 1281 | — | Accelerator Pedal 1 Channel 2 - Voltage Below Normal Value or Short Circuit to Ground | Full repair manual for code 1281 |
| 1282 | — | Throttle Position 2 - Voltage Below Normal Value or Short Circuit to Ground | Full repair manual for code 1282 |
| 1283 | — | Accelerator Pedal 2 Channel 2 - Voltage Below Normal Value or Short Circuit to Ground | Full repair manual for code 1283 |
| 1285 | — | Timeout of CAN Receive Message Com MS_Sys 1TO (Error Memory Slave) | Full repair manual for code 1285 |
| 1286 | — | Timeout of CAN Receive Message Com MS_Sys 2TO (Error Memory Slave) | Full repair manual for code 1286 |
| 1289 | — | Sensor Supply Voltage 1 from Engine Control Unit - Special Instructions | Full repair manual for code 1289 |
| 1289 | — | Timeout of CAN Receive Message Com MS_Sys 5TO (Error Memory Slave) | Full repair manual for code 1289 |
| 1290 | — | Sensor Supply Voltage 1 from Engine Control Unit Exceeds Physical Limit | Full repair manual for code 1290 |
| 1291 | — | Sensor Supply Voltage 1 from Engine Control Unit - Current Above Normal Range or Short Circuit to Ground | Full repair manual for code 1291 |
| 1291 | — | CAN Receiver Message Number Counter Error | Full repair manual for code 1291 |
| 1292 | — | Sensor Supply Voltage 1 from Engine Control Unit - Physical Limit Value Exceeded | Full repair manual for code 1292 |
| 1292 | — | CAN Receive Message Checksum Error | Full repair manual for code 1292 |
| 1293 | — | Sensor Supply Voltage 2 from Engine Control Unit - Special Instructions | Full repair manual for code 1293 |
| 1294 | — | Sensor Supply Voltage 2 from Engine Control Unit Exceeds Physical Limit | Full repair manual for code 1294 |
| 1295 | — | Sensor Supply Voltage 2 from Engine Control Unit - Current Above Normal Range or Short Circuit to Ground | Full repair manual for code 1295 |
