New Holland fault codes & repair guides
All 7,052 codes· 50 per page · page 77 of 142
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 13031 | INST | Hydraulic Oil Temperature Sensor Voltage Too Low | Full repair manual for code 13031, INST |
| 13032 | — | SB (Power Shuttle Control Unit) Error on +5V Reference Voltage | Full repair manual for code 13032 |
| 13033 | — | SC/SD (ECU for 4WD, front P.T.O. and lift) error on +5 V reference voltage | Full repair manual for code 13033 |
| 13040 | INST | Air to Air Intake Temperature Sensor Failure | Full repair manual for code 13040, INST |
| 13044 | INST | Fuel Shut Off Relay Latched with Short Detected | Full repair manual for code 13044, INST |
| 14000 | — | Seed Sensor Bus Communication Error | Full repair manual for code 14000 |
| 14001 | — | Rear P.T.O. sensor shorted to +12V | Full repair manual for code 14001 |
| 14001 | — | Rear PTO Speed Circuit Issue | Full repair manual for code 14001 |
| 14002 | — | Oil Filter Sensor Shorts to Ground When Power is Applied | Full repair manual for code 14002 |
| 14002 | — | Rear P.T.O. Sensor Shorted to Ground | Full repair manual for code 14002 |
| 14002 | New Holland Instrument Cluster | Transmission Oil Filter Switch Closed to Ground on Power Up | Full repair manual for code 14002, New Holland Instrument Cluster |
| 14003 | — | Hydraulic System Oil Filter Sensor Shorts to Ground | Full repair manual for code 14003 |
| 14003 | ICU | Hyd Oil Filter Switch Closed to Ground on Power Up | Full repair manual for code 14003, ICU |
| 14003 | New Holland Instrument Cluster | Hydraulic Oil Filter Switch Closed to Ground on Power Up | Full repair manual for code 14003, New Holland Instrument Cluster |
| 14005 | — | Rotational Speed Sensor of the PTO Shaft Error | Full repair manual for code 14005 |
| 14005 | New Holland Instrument Cluster | PTO Shaft Speed Sensor Error | Full repair manual for code 14005, New Holland Instrument Cluster |
| 14006 | New Holland Instrument Cluster | GOV Engine Speed Error | Full repair manual for code 14006, New Holland Instrument Cluster |
| 14008 | — | Oil Pressure Sensor Error | Full repair manual for code 14008 |
| 14008 | New Holland Instrument Cluster | Engine Oil Pressure Sensor Error | Full repair manual for code 14008, New Holland Instrument Cluster |
| 14010 | — | PTO Controller Disconnected from the Network | Full repair manual for code 14010 |
| 14010 | — | Seed Section Controller at Maximum Duty | Full repair manual for code 14010 |
| 14010 | New Holland Instrument Cluster | PTO Controller Off Line | Full repair manual for code 14010, New Holland Instrument Cluster |
| 14011 | — | Engine Speed Sensor Circuit Issue | Full repair manual for code 14011 |
| 14011 | — | Engine Speed Sensor Open Circuit Or Short To High Voltage | Full repair manual for code 14011 |
| 14011 | ICU | Communication Failure with Vehicle Data Bus 1 and All Other Controllers | Full repair manual for code 14011, ICU |
| 14012 | — | Vacuum Fan Controller at Maximum Duty | Full repair manual for code 14012 |
| 14013 | — | Steering Angle Sensor - Short Circuit to VCC | Full repair manual for code 14013 |
| 14014 | — | Engine Coolant Temperature Sensor Error | Full repair manual for code 14014 |
| 14014 | — | Steering Wheel Angle Sensor Fault | Full repair manual for code 14014 |
| 14014 | — | Steering Angle Sensor - Short Circuit to Ground or Open Circuit | Full repair manual for code 14014 |
| 14014 | New Holland Instrument Cluster | Engine Coolant Temperature Sensor Error | Full repair manual for code 14014, New Holland Instrument Cluster |
| 14015 | — | ADIC 5 Volt Reference Voltage Too Low | Full repair manual for code 14015 |
| 14015 | — | Engine Intake Air Temperature Sensor Error | Full repair manual for code 14015 |
| 14015 | — | 5V Power Supply Voltage - Too High | Full repair manual for code 14015 |
| 14015 | New Holland Instrument Cluster | Engine Intake Air Temperature Sensor Error | Full repair manual for code 14015, New Holland Instrument Cluster |
| 14016 | — | 5V Power Supply Voltage - Too Low | Full repair manual for code 14016 |
| 14017 | — | Voltage of Fuel Level Sensor Below Allowable Range | Full repair manual for code 14017 |
| 14017 | ICU | Fuel Level Sensor Voltage Out of Range Low | Full repair manual for code 14017, ICU |
| 14017 | New Holland Instrument Cluster | Fuel Level Sensor Voltage Out of Range Low | Full repair manual for code 14017, New Holland Instrument Cluster |
| 14018 | — | GOV module is disconnected from the network | Full repair manual for code 14018 |
| 14018 | ICU | GOV Off Line Fault | Full repair manual for code 14018, ICU |
| 14018 | New Holland Instrument Cluster | GOV Off Line Fault | Full repair manual for code 14018, New Holland Instrument Cluster |
| 14019 | — | Automatic Temperature Control System Disconnected from Network | Full repair manual for code 14019 |
| 14019 | ICU | ATC Off Line Fault | Full repair manual for code 14019, ICU |
| 14020 | New Holland Instrument Cluster | Loss of CAN Messages from the Secondary Steering Controller | Full repair manual for code 14020, New Holland Instrument Cluster |
| 14021 | — | Short to +12 V | Full repair manual for code 14021 |
| 14021 | — | Auxiliary Steering CAN Message Reception Failure | Full repair manual for code 14021 |
| 14021 | — | Radar Ground Speed Circuit Issue | Full repair manual for code 14021 |
| 14021 | — | Cranking Line Sensing Shorted to +12 V | Full repair manual for code 14021 |
| 14021 | New Holland Instrument Cluster | Secondary Steering Present and No CAN Messages Received | Full repair manual for code 14021, New Holland Instrument Cluster |
