New Holland fault codes & repair guides
All 7,052 codes· 50 per page · page 12 of 142
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 1024 | Hitch Controller | ICU CAN data bus signal lost. | Full repair manual for code 1024, Hitch Controller |
| 1025 | Hitch Controller (ATC / ICU) | Up/Down/Down Momentary switch value received from CAN data bus indicates switch failure. | Full repair manual for code 1025, Hitch Controller (ATC / ICU) |
| 1026 | Hitch | Up/Down remote fender switch failure | Full repair manual for code 1026, Hitch |
| 1027 | Armrest Controller (ARU) / Hitch Controller (ATC) / Electronic Draft Control (EDC) Module | Not Implemented / Lift Arm Position Voltage Low | Full repair manual for code 1027, Armrest Controller (ARU) / Hitch Controller (ATC) / Electronic Draft Control (EDC) Module |
| 1028 | Hitch Controller / Electronic Draft Control (EDC) or Alta Implement (ATC) | Travel Range potentiometer value received from CAN data bus indicates failure condition | Full repair manual for code 1028, Hitch Controller / Electronic Draft Control (EDC) or Alta Implement (ATC) |
| 1029 | Armrest Controller (ARU) or Hitch / ATC (Alta Implement) Controller | Drop Rate value received from CAN data bus indicates potentiometer failure condition. | Full repair manual for code 1029, Armrest Controller (ARU) or Hitch / ATC (Alta Implement) Controller |
| 1030 | Hitch Controller | Right draft pin voltage is outside the normal operating range. (CCH Only). | Full repair manual for code 1030, Hitch Controller |
| 1031 | CCH (Central Controller Hitch) | Left draft pin voltage is outside the normal operating range. (CCH Only) | Full repair manual for code 1031, CCH (Central Controller Hitch) |
| 1032 | Hitch Controller | Ground speed failure-value received from CAN data bus indicates failure condition. | Full repair manual for code 1032, Hitch Controller |
| 1033 | Hitch Controller | Slip Limit Set Point received from CAN data bus indicates failure condition. | Full repair manual for code 1033, Hitch Controller |
| 1034 | Hitch Controller | Slip Enable switch received from CAN data bus indicates failure condition | Full repair manual for code 1034, Hitch Controller |
| 1035 | Hitch Controller | The Percent slip received from ETC indicates failure condition | Full repair manual for code 1035, Hitch Controller |
| 1036 | ARU (Arm Rest Unit / Arm Rest Module) | The ARU reports EDC Inching Up switch faulty or not available. | Full repair manual for code 1036, ARU (Arm Rest Unit / Arm Rest Module) |
| 1037 | Hitch Controller / ARU (Arm Rest Unit / Armrest Module) | The ARU reports EDC Inching Down switch faulty or not available | Full repair manual for code 1037, Hitch Controller / ARU (Arm Rest Unit / Armrest Module) |
| 1039 | ARM | PTO Switch Failure | Full repair manual for code 1039, ARM |
| 1040 | — | Lift Not Calibrated | Full repair manual for code 1040 |
| 1041 | ENGINE | Engine Overrun | Full repair manual for code 1041, ENGINE |
| 1041 | ENGINE | Engine RPM Exceeds Maximum Limit | Full repair manual for code 1041, ENGINE |
| 1042 | — | Lowering Limit Potentiometer Not Set on Maximum Value | Full repair manual for code 1042 |
| 1043 | — | Lowering Speed Potentiometer Not Set on Maximum Value | Full repair manual for code 1043 |
| 1044 | — | Set Position/Draft Control Potentiometer Not in Position | Full repair manual for code 1044 |
| 1045 | — | Fuel Level Sensor Open Circuit | Full repair manual for code 1045 |
| 1045 | IC | Fuel Level Monitoring: Open Circuit | Full repair manual for code 1045, IC |
| 1049 | — | Fluid Supply Sensor in Hydrostatic - Open Circuit or Short to Ground | Full repair manual for code 1049 |
| 1049 | — | Wheel Speed Sensor Open Circuit | Full repair manual for code 1049 |
| 1051 | — | No CAN Communication With Engine Controller | Full repair manual for code 1051 |
| 1051 | ENGINE | Loss of CAN Communication with Engine | Full repair manual for code 1051, ENGINE |
| 1053 | — | 5 Volt Reference Shorted to +VE Voltage | Full repair manual for code 1053 |
| 1053 | — | 5V Reference Voltage No. 3 - High Voltage | Full repair manual for code 1053 |
| 1054 | — | 5V reference voltage No. 3 - reduced voltage | Full repair manual for code 1054 |
| 1054 | — | Short Circuit of the 5 V Supply Voltage to 'Ground' | Full repair manual for code 1054 |
| 1054 | — | 5 Volt Reference Short To Ground | Full repair manual for code 1054 |
| 1058 | — | Timeout of CAN message EDC2BC | Full repair manual for code 1058 |
| 1059 | — | 8 V Support Voltage Error in Traction Load Contacts | Full repair manual for code 1059 |
| 1059 | — | 8 Volt Reference Error (Draft Load Pins) | Full repair manual for code 1059 |
| 1059 | — | Working Arm Hitch Electronic Draft Control Diagnostic Error | Full repair manual for code 1059 |
| 1059 | — | 5 Volt Reference Open Circuit | Full repair manual for code 1059 |
| 1059 | ARM | Hitch SLIP Switch Failure | Full repair manual for code 1059, ARM |
| 1063 | — | Break in the circuit of the lower electromagnet of the EDC hydraulic valve | Full repair manual for code 1063 |
| 1064 | — | Open Circuit on the Lifting Control Solenoid Valve | Full repair manual for code 1064 |
| 1065 | ARU (Arm Rest Unit / Armrest Control Module) | The ARU specified tractor without draft control (position only hitch) but detected presence of draft pin(s). | Full repair manual for code 1065, ARU (Arm Rest Unit / Armrest Control Module) |
| 1066 | — | Lifting Control Solenoid Valve Shorted | Full repair manual for code 1066 |
| 1066 | — | Raise Solenoid Short Circuit | Full repair manual for code 1066 |
| 1067 | — | Hydraulic Valve Power Voltage Is Too Low | Full repair manual for code 1067 |
| 1067 | — | Drawbar Contact Sensor Not Detected | Full repair manual for code 1067 |
| 1067 | — | EDC Hydraulic Valve Supply Too Low | Full repair manual for code 1067 |
| 1067 | New Holland Electronic Draft Control | Draft Control Specified but No Draft Pin Detected | Full repair manual for code 1067, New Holland Electronic Draft Control |
| 1068 | — | Max. raise limit potentiometer not set on maximum value | Full repair manual for code 1068 |
| 1068 | — | Height Limit Control Not Set To Maximum During Calibration | Full repair manual for code 1068 |
| 1069 | — | HITCH Electronic Draft Control Malfunction | Full repair manual for code 1069 |
