New Holland fault codes & repair guides
All 7,052 codes· 50 per page · page 134 of 142
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| TMF 175 | TMF (Tractor Multi-Function) Controller | PTO Clutch has not reached lock up speed within 6 seconds of being turned ON | Full repair manual for code TMF 175, TMF (Tractor Multi-Function) Controller |
| TMF 178 | TMF (Tractor Multifunction Controller) | PTO speed sensor has been changed. | Full repair manual for code TMF 178, TMF (Tractor Multifunction Controller) |
| TMF 179 | PTO Controller | The PTO is receiving no frequency from the Shaft Size Sensor on a two speed PTO. | Full repair manual for code TMF 179, PTO Controller |
| TMF 18 | TMF (Tractor Multifunction Controller) | Hitch Rockshaft Position potentiometer is outside its normal operating range | Full repair manual for code TMF 18, TMF (Tractor Multifunction Controller) |
| TMF 180 | PTO Controller | The PTO is receiving signals from the Shaft Size Sensor on a single speed PTO configuration. | Full repair manual for code TMF 180, PTO Controller |
| TMF 19 | Armrest Controller | Hitch Upper Limit potentiometer has failed in the Armrest Controller | Full repair manual for code TMF 19, Armrest Controller |
| TMF2 | — | Hitch Raise Solenoid Shorted to 12 Volts | Full repair manual for code TMF2 |
| TMF 21 | Armrest Controller (ARU) | Hitch Load Command potentiometer is failed in the Armrest Controller | Full repair manual for code TMF 21, Armrest Controller (ARU) |
| TMF 22 | TMF | Single draft pin sensor failed when configured for one draft pin sensor. | Full repair manual for code TMF 22, TMF |
| TMF 23 | TMF (Tractor Multi-Function) Controller or CCH (Hitch Controller) | Two draft pin sensors failed when configured for two draft pins. | Full repair manual for code TMF 23, TMF (Tractor Multi-Function) Controller or CCH (Hitch Controller) |
| TMF 24 | TMF (Tractor Multifunction Controller) | Communications Lost with Instrumentation Controller | Full repair manual for code TMF 24, TMF (Tractor Multifunction Controller) |
| TMF 25 | Armrest Controller | Hitch Up/Down Switch failed in the Armrest controller | Full repair manual for code TMF 25, Armrest Controller |
| TMF 26 | TMF (Tractor Multi-Function) Controller | Fender UP and DOWN switch failure or both switches simultaneously pressed | Full repair manual for code TMF 26, TMF (Tractor Multi-Function) Controller |
| TMF 28 | Armrest Controller (ARM) | Hitch Travel potentiometer is failed in the Armrest Controller | Full repair manual for code TMF 28, Armrest Controller (ARM) |
| TMF 29 | TMF (Tractor Multi-Function) Controller | Hitch Drop Rate potentiometer is failed in the Armrest Controller | Full repair manual for code TMF 29, TMF (Tractor Multi-Function) Controller |
| TMF 3 | TMF Controller | Hitch Raise Solenoid High Side Driver shorted to 12 volts. | Full repair manual for code TMF 3, TMF Controller |
| TMF 30 | TMF (Tractor Management Framework) | Right Draft Pin voltage is outside the normal operating range. | Full repair manual for code TMF 30, TMF (Tractor Management Framework) |
| TMF 31 | TMF (Tractor Multi-Function) Controller | Left Draft Pin voltage is outside the normal operating range | Full repair manual for code TMF 31, TMF (Tractor Multi-Function) Controller |
| TMF 32 | Instrumentation Controller | Ground Speed Signal is failed in the Instrumentation Controller | Full repair manual for code TMF 32, Instrumentation Controller |
| TMF 33 | Armrest Controller | Hitch Slip Set Switch failed in the Armrest controller | Full repair manual for code TMF 33, Armrest Controller |
| TMF 34 | Hitch Controller (TMF) | Hitch Slip Select Switch failed in the Armrest controller | Full repair manual for code TMF 34, Hitch Controller (TMF) |
| TMF 35 | Instrumentation Controller (ICU) | Slip Sensor (radar or wheel speed) is failed in the Instrumentation Controller | Full repair manual for code TMF 35, Instrumentation Controller (ICU) |
| TMF 37 | TMF (Tractor Multi-Function) Controller | The ARU reports EDC Transport Lock is faulty or not available. | Full repair manual for code TMF 37, TMF (Tractor Multi-Function) Controller |
| TMF 4 | TMF (Tractor Management Framework) | Hitch Raise Solenoid Failed Open or Shorted to Ground | Full repair manual for code TMF 4, TMF (Tractor Management Framework) |
| TMF 41 | TMF (Tractor Multi-Function) Controller / ARU (Armrest Controller) | Draft pin(s) detected but the Armrest controller specified tractor without draft control. | Full repair manual for code TMF 41, TMF (Tractor Multi-Function) Controller / ARU (Armrest Controller) |
| TMF 42 | TMF (Tractor Multi-Function) Controller | Engine speed must be set above 1600 rpm during calibration of lower valve | Full repair manual for code TMF 42, TMF (Tractor Multi-Function) Controller |
| TMF 43 | TMF (Tractor Multifunction Controller) | No Draft pin(s) detected but the Armrest controller specified tractor with draft control. | Full repair manual for code TMF 43, TMF (Tractor Multifunction Controller) |
| TMF 44 | Armrest Controller or Hitch Controller (Electronic Draft Control / EDC module) | Hitch calibration aborted due to tractor movement. | Full repair manual for code TMF 44, Armrest Controller or Hitch Controller (Electronic Draft Control / EDC module) |
| TMF 45 | TMF (Tractor Multi-Function) Controller | Hitch Calibration Attempted Without Engine Running or Lost Engine Speed Signal | Full repair manual for code TMF 45, TMF (Tractor Multi-Function) Controller |
| TMF 47 | Hitch Controller / Tractor Management Function (TMF) module | Raise Valve calibration value is too high. (valve problem) | Full repair manual for code TMF 47, Hitch Controller / Tractor Management Function (TMF) module |
| TMF 48 | TMF (Tractor Multifunction Controller) | Raise Valve calibration value is too low. (valve problem) | Full repair manual for code TMF 48, TMF (Tractor Multifunction Controller) |
| TMF 5 | TMF (Tractor Multifunction Controller) | Hitch Lower Solenoid Shorted to 12 volts | Full repair manual for code TMF 5, TMF (Tractor Multifunction Controller) |
| TMF 50 | TMF (Tractor Management Frame) | Hitch position at top of travel is not within specification during calibration. | Full repair manual for code TMF 50, TMF (Tractor Management Frame) |
| TMF 51 | TMF (Tractor Multi-Function) Controller | Lower Valve calibration value is too high. (valve problem) | Full repair manual for code TMF 51, TMF (Tractor Multi-Function) Controller |
| TMF 52 | TMF Controller | Lower Valve calibration value is too low. (valve problem) | Full repair manual for code TMF 52, TMF Controller |
| TMF 53 | TMF (Tractor Multi-Function) Controller | The time allowed for hitch calibration has expired. | Full repair manual for code TMF 53, TMF (Tractor Multi-Function) Controller |
| TMF 54 | TMF (Tractor Multi-Function) Controller | Hitch position at bottom of travel is not within specification during calibration. | Full repair manual for code TMF 54, TMF (Tractor Multi-Function) Controller |
| TMF 55 | TMF Controller | Hitch position range from top to bottom is not within spec during calibration. | Full repair manual for code TMF 55, TMF Controller |
| TMF 56 | TMF | Hitch position range to position command range ratio is not within spec during calibration | Full repair manual for code TMF 56, TMF |
| TMF 57 | TMF (Tractor Multi-Function) | Right Draft Pin voltage is not within spec for 'no load' condition during calibration. | Full repair manual for code TMF 57, TMF (Tractor Multi-Function) |
| TMF 58 | TMF (Tractor Multi-Function) Controller | Left Draft Pin voltage is not within spec for ‘no load’ condition during calibration. | Full repair manual for code TMF 58, TMF (Tractor Multi-Function) Controller |
| TMF 59 | TMF (Tractor Multi-Function) Controller | Both Draft Pin voltages are not within spec for ‘no load’ condition during calibration | Full repair manual for code TMF 59, TMF (Tractor Multi-Function) Controller |
| TMF 6 | Tractor Multifunction Controller (TMF) | Hitch Lower Solenoid High Side Driver circuit short to 12 volts | Full repair manual for code TMF 6, Tractor Multifunction Controller (TMF) |
| TMF 60 | TMF (Tractor Multi-Function) Controller | Draft pin connected to left vs right for single pin setup during calibration. | Full repair manual for code TMF 60, TMF (Tractor Multi-Function) Controller |
| TMF 61 | TMF (Tractor Multi Function) Controller | The Hitch Calibration procedure must be performed | Full repair manual for code TMF 61, TMF (Tractor Multi Function) Controller |
| TMF 62 | TMF (Tractor Multi-Function Controller) | Communications Lost with Performance Monitor Function | Full repair manual for code TMF 62, TMF (Tractor Multi-Function Controller) |
| TMF 63 | TMF (Tractor Multi-Function) Controller | Controller 8-volt reference is too high (above 8.8 volts) | Full repair manual for code TMF 63, TMF (Tractor Multi-Function) Controller |
| TMF 64 | TMF (Tractor Multi-Function) Controller | Controller 8 volt reference is too low (below 7.2 volts) | Full repair manual for code TMF 64, TMF (Tractor Multi-Function) Controller |
| TMF 65 | TMF | Battery Voltage is too Low | Full repair manual for code TMF 65, TMF |
| TMF 66 | TMF | Battery Voltage is too Low | Full repair manual for code TMF 66, TMF |
