Case IH fault codes & repair guides
All 9,847 codes· 50 per page · page 141 of 197
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 54150 | Instrumentation Controller (INST) or Performance Controller | Communications Lost with Hitch Controller | Full repair manual for code 54150, Instrumentation Controller (INST) or Performance Controller |
| 54170 | PTO Controller | Communication Lost With The Performance Controller | Full repair manual for code 54170, PTO Controller |
| 54211 | — | Clutch is Slipping Too Much | Full repair manual for code 54211 |
| 54221 | PTO Controller | PTO Shaft rotation is NOT detected when PTO engagement is attempted | Full repair manual for code 54221, PTO Controller |
| 54241 | — | Shaft Rotation Detected When Engine Is OFF | Full repair manual for code 54241 |
| 54251 | PTO Controller System | PTO Shaft rotation is detected when the PTO clutch is OFF | Full repair manual for code 54251, PTO Controller System |
| 54272 | PTO Controller | PTO Shaft Overspeed Detected | Full repair manual for code 54272, PTO Controller |
| 54282 | PTO Controller | PTO Clutch has not reached lock up speed within 6 seconds of being turned ON. | Full repair manual for code 54282, PTO Controller |
| 55005 | Auxiliary Valve Controller (AUX), Armrest Controller, or Engine ECU | Measured 'Rear PVE -Command' voltage is out of range / Fuel HCI temperature sensor voltage is above/below the applicable range | Full repair manual for code 55005, Auxiliary Valve Controller (AUX), Armrest Controller, or Engine ECU |
| 55010 | ECU / Transmission Controller | Illegal operation. Incorrect map structure (55010) / Internal Output Enable Latch Failed (56091) | Full repair manual for code 55010, ECU / Transmission Controller |
| 55011 | Engine Control Unit (ECU) / Aftertreatment Control Module | Hydrocarbon Injection (HCI) Pump Malfunction | Full repair manual for code 55011, Engine Control Unit (ECU) / Aftertreatment Control Module |
| 55012 | Implement control module / Pro 1200 display | Granular chemical meter sensor failure | Full repair manual for code 55012, Implement control module / Pro 1200 display |
| 55013 | — | The 'Bypass' spool is stuck in the on position. | Full repair manual for code 55013 |
| 55014 | — | "Front PVE - status" error signal from valve | Full repair manual for code 55014 |
| 55014 | STEERING Controller | Voltage is detected on the FRONT_STEER_RIGHT driver pin when not expected | Full repair manual for code 55014, STEERING Controller |
| 55015 | — | Rear PVE - status error signal from valve | Full repair manual for code 55015 |
| 55017 | — | Voltage is detected on the 'Front PVE-Power' driver pin when not expected. | Full repair manual for code 55017 |
| 55019 | STEERING | Voltage is detected on the RELAY driver pin when not expected. | Full repair manual for code 55019, STEERING |
| 55021 | Transmission Control Unit (TCU) | Transmission pressure sensors and switches | Full repair manual for code 55021, Transmission Control Unit (TCU) |
| 55022 | STEERING Control Module (Steering ECU) | ARTIC_BYPASS Driver Pin Voltage Not Detected | Full repair manual for code 55022, STEERING Control Module (Steering ECU) |
| 55023 | — | The 'Bypass' spool is stuck in the off position | Full repair manual for code 55023 |
| 55027 | — | Voltage is not detected on the 'Front PVE-Power' driver pin when expected | Full repair manual for code 55027 |
| 55028 | STEERING | VOLTAJE DETECTADO EN PIN C057-10 | Full repair manual for code 55028, STEERING |
| 55034 | Steering Controller | Internal Controller Failure | Full repair manual for code 55034, Steering Controller |
| 55042 | STEERING | No current is sensed flowing through the ARTIC_BYPASS driver pin when expected | Full repair manual for code 55042, STEERING |
| 55047 | Steering Control System / Steering ECU | No current is sensed flowing through the MAKEUP_RIGHT driver when expected. | Full repair manual for code 55047, Steering Control System / Steering ECU |
| 55048 | Steering Control Module / Steering ECU | Low current passing through the left driver | Full repair manual for code 55048, Steering Control Module / Steering ECU |
| 55049 | Steering Controller (STEERING) | No current is sensed flowing through the RELAY driver pin when expected | Full repair manual for code 55049, Steering Controller (STEERING) |
| 55052 | STEERING | Too much current is sensed flowing through the ARTIC_BYPASS driver pin | Full repair manual for code 55052, STEERING |
| 55054 | STEERING Controller | Overcurrent condition on a steering driver circuit | Full repair manual for code 55054, STEERING Controller |
| 55055 | Steering Controller | Overcurrent in the steering system (FRONT_STEER_LEFT driver pin) | Full repair manual for code 55055, Steering Controller |
| 55057 | Steering Control Module | Too much current is sensed flowing through the MAKEUP_RIGHT driver pin | Full repair manual for code 55057, Steering Control Module |
| 55061 | STEERING Controller | Orbitrol (Hand Pump) Pressure Signal is Out of Range | Full repair manual for code 55061, STEERING Controller |
| 55062 | STEERING | Measured 'Steering Wheel Motion Signal A' voltage is out of range | Full repair manual for code 55062, STEERING |
| 55081 | Tractor Management Controller (TMF), Auto-Guidance Controller (NavController), or Steering Controller | Movement commanded to the 'Front Steer' does not match the movement detected | Full repair manual for code 55081, Tractor Management Controller (TMF), Auto-Guidance Controller (NavController), or Steering Controller |
| 55082 | Steering Control Module | Articulation/Steering Movement Mismatch | Full repair manual for code 55082, Steering Control Module |
| 55083 | STEERING | Articulation movement does not match the steering wheel | Full repair manual for code 55083, STEERING |
| 55091 | NAV Controller / Steering Controller | Front Steer movement with no command | Full repair manual for code 55091, NAV Controller / Steering Controller |
| 55093 | Transmission Controller | Transmission Controller Pressure Sensor Circuit Fault | Full repair manual for code 55093, Transmission Controller |
| 56001 | Transmission Controller (TRANS) | Shuttle Shift Attempted From A Gear Higher Than Shuttle Shifting Allowed | Full repair manual for code 56001, Transmission Controller (TRANS) |
| 56002 | Transmission Controller | The Transmission Controller Calibration Procedure Must Be Performed. | Full repair manual for code 56002, Transmission Controller |
| 56003 | Transmission Controller (TRANS) | Controller Memory Error -- Loss of Forward Gear Pre-selection information. | Full repair manual for code 56003, Transmission Controller (TRANS) |
| 56004 | Transmission Controller (TRANS / TECU) | Measured transmission output speed does not match the commanded transmission output speed | Full repair manual for code 56004, Transmission Controller (TRANS / TECU) |
| 56005 | Transmission Controller (TRANS) | The stored Forward Gear Limit is invalid. | Full repair manual for code 56005, Transmission Controller (TRANS) |
| 56014 | Transmission Controller (TRANS / TRCU) | The Transmission Control Lever is NOT in Park, Neutral, Forward, or Reverse. | Full repair manual for code 56014, Transmission Controller (TRANS / TRCU) |
| 56016 | Transmission Controller (TRANS) | Clutch Pedal Position Sensor Does Not Agree With Bottom of Clutch Pedal Switch. | Full repair manual for code 56016, Transmission Controller (TRANS) |
| 56022 | Transmission Controller (TRANS) | Battery Voltage below valve operational limit (9V) | Full repair manual for code 56022, Transmission Controller (TRANS) |
| 56023 | Transmission Controller (TRANS) | 1F Valve Coil circuit is shorted to 12 volts when the valve is ON. | Full repair manual for code 56023, Transmission Controller (TRANS) |
| 56024 | Transmission Controller (TRANS) | 1M Valve Coil Circuit is Shorted to 12 Volts When Valve is On | Full repair manual for code 56024, Transmission Controller (TRANS) |
| 56025 | Transmission Controller (TRANS) | 1R Valve Coil circuit is shorted to 12 volts when the valve is ON. | Full repair manual for code 56025, Transmission Controller (TRANS) |
