Case IH fault codes & repair guides
All 9,847 codes· 50 per page · page 17 of 197
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 1013 | Hitch | No communication with the ICP (Instrument Cluster Panel) | Full repair manual for code 1013, Hitch |
| 1013 | Hitch Controller / EDC (Electronic Draft Control) module or Armrest / ICP (Instrument Cluster Panel) controller | Drop rate control potentiometer - signal too high | Full repair manual for code 1013, Hitch Controller / EDC (Electronic Draft Control) module or Armrest / ICP (Instrument Cluster Panel) controller |
| 1013 | ISM-DI | Battery 5V Reference 2 Circuit High | Full repair manual for code 1013, ISM-DI |
| 1014 | Cluster or UCM | Cluster System Voltage Above Normal (>16.5V) | Full repair manual for code 1014, Cluster or UCM |
| 1014 | Hitch Controller | Right-hand load sensing pin - signal too low | Full repair manual for code 1014, Hitch Controller |
| 1014 | Hitch Control Module | 5-volt reference voltage is above the upper voltage limit | Full repair manual for code 1014, Hitch Control Module |
| 1014 - UCM | UCM | Right-hand load sensing pin - signal too low | Full repair manual for code 1014 - UCM, UCM |
| 1015 | Hitch Electronic Control Panel / Electronic Draft Control (EDC) module or Transmission/Chassis Controller (XCM) | Right-hand draft pin sensor - signal too high | Full repair manual for code 1015, Hitch Electronic Control Panel / Electronic Draft Control (EDC) module or Transmission/Chassis Controller (XCM) |
| 1015 | INST or INST2 (Instrument Panel Controller) | Seat Switch may be stuck closed | Full repair manual for code 1015, INST or INST2 (Instrument Panel Controller) |
| 1015 | Instrument Cluster (IC) or Universal Control Module (UCM) | Cluster System Voltage Below Normal (<11.5V) | Full repair manual for code 1015, Instrument Cluster (IC) or Universal Control Module (UCM) |
| 1015 - UCM | UCM | Right-hand load sensing pin - signal too high | Full repair manual for code 1015 - UCM, UCM |
| 1015 | XCM (Multi-function Control Module) | Right-hand load sensing pin - signal too high | Full repair manual for code 1015, XCM (Multi-function Control Module) |
| 1016 | Armrest Controller / Hitch/Draft Control Module | L/H load sensing pin - signal too low | Full repair manual for code 1016, Armrest Controller / Hitch/Draft Control Module |
| 1016 | Hitch Controller / Armrest Controller / PTO Controller / Draft Controller | Not implemented / PTO Switch Open Circuit / L/H Load Sensing Pin Signal Too Low | Full repair manual for code 1016, Hitch Controller / Armrest Controller / PTO Controller / Draft Controller |
| 1016 | PTO Controller | PTO ON switch wire connection from Armrest to PTO failed Open Circuit | Full repair manual for code 1016, PTO Controller |
| 1016 - UCM | UCM / XCM / EDC / Armrest module | Left-hand load sensing pin - signal too low | Full repair manual for code 1016 - UCM, UCM / XCM / EDC / Armrest module |
| 1017 | PTO Controller | PTO ON switch wire connection from Armrest to PTO failed Short Circuit. | Full repair manual for code 1017, PTO Controller |
| 1017 | Tractor Control Unit (TCU) / Armrest Controller (ARU) | Hitch Position Command Potentiometer Failure | Full repair manual for code 1017, Tractor Control Unit (TCU) / Armrest Controller (ARU) |
| 1017 - UCM | UCM | Left-hand load sensing pin - signal too high | Full repair manual for code 1017 - UCM, UCM |
| 1017 | XCM (Multi-function Control Module) | Left-hand load sensing pin - signal too high | Full repair manual for code 1017, XCM (Multi-function Control Module) |
| 1018 | Hitch Controller | Hitch rockshaft position potentiometer open/short/misadjust or circuit failure | Full repair manual for code 1018, Hitch Controller |
| 1018 | Hitch Control Module | Both draft load sensing pins disconnected | Full repair manual for code 1018, Hitch Control Module |
| 1018 - UCM | UCM / XCM | Both load sensing pins disconnected | Full repair manual for code 1018 - UCM, UCM / XCM |
| 1019 | Hitch / EDC (Electronic Draft Control) Controller | Load sensing pin 8V reference - voltage too low YES | Full repair manual for code 1019, Hitch / EDC (Electronic Draft Control) Controller |
| 1019 | Tractor Control Unit (TCU) / Armrest Controller Module (ACM) | Upper limit potentiometer failure | Full repair manual for code 1019, Tractor Control Unit (TCU) / Armrest Controller Module (ACM) |
| 1020 | Armrest Controller | Aux remote valve RETRACT LIMIT SET switch is failed | Full repair manual for code 1020, Armrest Controller |
| 1020 | HITCH Controller | Hitch Slip Select Switch failed in the Armrest controller | Full repair manual for code 1020, HITCH Controller |
| 1020 | XCM (Multi-function Control Module) or EDC (Electronic Draft Control) / Hitch Controller | Load sensing pin 8V reference - voltage too high | Full repair manual for code 1020, XCM (Multi-function Control Module) or EDC (Electronic Draft Control) / Hitch Controller |
| 1021 | Armrest Controller (ARM) or Tractor Management Function (TMF) / Hitch Controller | Load command potentiometer failure | Full repair manual for code 1021, Armrest Controller (ARM) or Tractor Management Function (TMF) / Hitch Controller |
| 1021 | EDC (Electronic Draft Control) / Hitch Control Module | Draft sensitivity control potentiometer - voltage too low (short or open circuit) | Full repair manual for code 1021, EDC (Electronic Draft Control) / Hitch Control Module |
| 1022 | EDC (Electronic Draft Control) / XCM (Central Controller) | Draft sensitivity control potentiometer – voltage too high | Full repair manual for code 1022, EDC (Electronic Draft Control) / XCM (Central Controller) |
| 1022 | Hitch Controller (CCH / Armrest Controller / TMF) | Single draft pin sensor failed when configured for one draft pin sensor.(CCH Only) | Full repair manual for code 1022, Hitch Controller (CCH / Armrest Controller / TMF) |
| 1023 | ATC (Armrest Tractor Controller), CCH (Central Controller Hitch), or EDC (Electronic Draft Control) | Command arm / EDC control panel is disconnected | Full repair manual for code 1023, ATC (Armrest Tractor Controller), CCH (Central Controller Hitch), or EDC (Electronic Draft Control) |
| 1023 | Hitch (CCH or TCU) | Two draft pin sensors failed when configured for two draft pins. (CCH Only) | Full repair manual for code 1023, Hitch (CCH or TCU) |
| 1024 | Hitch Controller | ICU CAN data bus signal lost. | Full repair manual for code 1024, Hitch Controller |
| 1024 | Hitch Controller | Perform the hydraulic lift calibration | Full repair manual for code 1024, Hitch Controller |
| 1024 | INST | Trans oil filter switch shorted to ground on power up | Full repair manual for code 1024, INST |
| 1024 - UCM | UCM | Perform the hydraulic lift calibration | Full repair manual for code 1024 - UCM, UCM |
| 1025 | Armrest Controller (ARM) | Hitch Up/Down Momentary Switch Failure | Full repair manual for code 1025, Armrest Controller (ARM) |
| 1025 | EDC (Electronic Draft Control) module, CCU (Central Control Unit), or Hitch Electronic Control Panel | Position control potentiometer - signal too low | Full repair manual for code 1025, EDC (Electronic Draft Control) module, CCU (Central Control Unit), or Hitch Electronic Control Panel |
| 1025 | Engine Controller (EDC / ECU), Universal Control Module (UCM), or Instrument Cluster (IC) | Foot Throttle Sensor Is Above Range - Shorted To Power | Full repair manual for code 1025, Engine Controller (EDC / ECU), Universal Control Module (UCM), or Instrument Cluster (IC) |
| 1026 | Hitch Controller | Up/Down remote fender switch failure | Full repair manual for code 1026, Hitch Controller |
| 1026 | Hitch Control Module (CCU), Electronic Draft Control (EDC), or Armrest Controller | Position control potentiometer - signal too high | Full repair manual for code 1026, Hitch Control Module (CCU), Electronic Draft Control (EDC), or Armrest Controller |
| 1026 | IC (Instrument Cluster) | Hand Throttle Sensor Is Above Range - Shorted To Power | Full repair manual for code 1026, IC (Instrument Cluster) |
| 1027 | Electronic Draft Control (EDC) / Hitch Control Module | Lift arm position sensor - voltage too low | Full repair manual for code 1027, Electronic Draft Control (EDC) / Hitch Control Module |
| 1027 | Hitch Control Module | Not implemented / Lift arm position sensing control voltage low | Full repair manual for code 1027, Hitch Control Module |
| 1027 - UCM | UCM | Lift arm position sensor - voltage too low | Full repair manual for code 1027 - UCM, UCM |
| 1028 | Hitch Controller (EDC) | Travel Range potentiometer failure | Full repair manual for code 1028, Hitch Controller (EDC) |
| 1028 | Hitch Electronic Control Panel / CCU (Central Control Unit) / ATC (Armrest/Tractor Controller) | Lift arm position sensor - voltage too high | Full repair manual for code 1028, Hitch Electronic Control Panel / CCU (Central Control Unit) / ATC (Armrest/Tractor Controller) |
| 1028 - UCM | UCM | Lift arm position sensor – voltage too high | Full repair manual for code 1028 - UCM, UCM |
