Case IH fault codes & repair guides
All 9,847 codes· 50 per page · page 91 of 197
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 9060 - UCM | UCM | Front hitch 14bar accumulator solenoid - open circuit or short circuit to ground | Full repair manual for code 9060 - UCM, UCM |
| 9061 | PTO Controller | PTO Shaft Speed Sensor and PTO Shaft Size Sensor Connections Swapped | Full repair manual for code 9061, PTO Controller |
| 9061 - UCM | UCM | Front hitch 40bar accumulator solenoid open circuit / short circuit to ground | Full repair manual for code 9061 - UCM, UCM |
| 9062 - UCM | UCM | Front hitch single/double acting solenoid 1 open circuit / short circuit to ground | Full repair manual for code 9062 - UCM, UCM |
| 9067 - UCM | UCM | Short circuit to 12V on the Front hitch single/double acting solenoid 1 circuit | Full repair manual for code 9067 - UCM, UCM |
| 9069 - UCM | UCM | Short circuit to 12V on front hitch 14bar accumulator solenoid | Full repair manual for code 9069 - UCM, UCM |
| 9070 - UCM | UCM | Front hitch single/double acting solenoid 2 - open circuit / short circuit to 0V | Full repair manual for code 9070 - UCM, UCM |
| 9071 | PTO Controller | The PTO is receiving no frequency from the Shaft Size Sensor on a two speed PTO configuration | Full repair manual for code 9071, PTO Controller |
| 9071 - UCM | UCM | Front hitch single/double acting solenoid 2 short circuit to 12V | Full repair manual for code 9071 - UCM, UCM |
| 9081 | PTO Controller | PTO Speed Sensor Configuration Error | Full repair manual for code 9081, PTO Controller |
| 9099 | Front Hitch Controller or Vehicle Electronic Control Unit (VECU) / ICU3 | Front hitch management option not enabled. | Full repair manual for code 9099, Front Hitch Controller or Vehicle Electronic Control Unit (VECU) / ICU3 |
| 9151 | UCM (Universal Control Module) | Bus-Warn at CAN-Bus No.1 | Full repair manual for code 9151, UCM (Universal Control Module) |
| 9152 | UCM | Bus-Warn at CAN-Bus No.1 | Full repair manual for code 9152, UCM |
| 9153 | Master Vehicle Controller (UCM) or Instrument Cluster (IC) | Timeout of CAN Message EEC1 | Full repair manual for code 9153, Master Vehicle Controller (UCM) or Instrument Cluster (IC) |
| 9154 | UCM (Universal Control Module) | Timeout of CAN Message TSC1 | Full repair manual for code 9154, UCM (Universal Control Module) |
| 9156 | UCM | Hydraulic Enable Button Error From AIC | Full repair manual for code 9156, UCM |
| 9158 | UCM | H Pattern Indicator Shorted To Ground | Full repair manual for code 9158, UCM |
| 9159 | UCM (Universal Control Module) | ISO Pattern Indicator Shorted To Ground | Full repair manual for code 9159, UCM (Universal Control Module) |
| 9160 | UCM (Universal Control Module) | H Pattern Indicator Shorted To Power | Full repair manual for code 9160, UCM (Universal Control Module) |
| 9161 | UCM (Universal Control Module) or IC (Instrument Cluster) | ISO Pattern Indicator Shorted To Power | Full repair manual for code 9161, UCM (Universal Control Module) or IC (Instrument Cluster) |
| 9301 | Hitch Controller | Raise Valve calibration value is too high (valve problem) | Full repair manual for code 9301, Hitch Controller |
| 9302 | Hitch Controller or Armrest Controller | Raise Valve calibration value is too low (valve problem) | Full repair manual for code 9302, Hitch Controller or Armrest Controller |
| 9303 | HITCH Controller | Raise Valve current measurement problem during calibration. | Full repair manual for code 9303, HITCH Controller |
| 9304 | HITCH Controller | Hitch position at top of travel is not within specification during calibration | Full repair manual for code 9304, HITCH Controller |
| 9306 | Hitch Controller | Lower Valve calibration value is too high (valve problem) | Full repair manual for code 9306, Hitch Controller |
| 9307 | HITCH | Lower Valve calibration value is too low | Full repair manual for code 9307, HITCH |
| 9308 | Hitch Controller | The time allowed for hitch calibration has expired. | Full repair manual for code 9308, Hitch Controller |
| 9309 | HITCH Controller (Electronic Draft Control / EDC module) or ARM (Armrest Controller) | Hitch position at bottom of travel is not within specification during calibration | Full repair manual for code 9309, HITCH Controller (Electronic Draft Control / EDC module) or ARM (Armrest Controller) |
| 9310 | Hitch Controller | Hitch position range from top to bottom is not within spec during calibration. | Full repair manual for code 9310, Hitch Controller |
| 9311 | HITCH Controller | Hitch position to hitch rockshaft position ratio is not within spec during calibration. | Full repair manual for code 9311, HITCH Controller |
| 9312 | Hitch Controller | Invalid Configuration - Draft pin connected to left vs right for single pin setup | Full repair manual for code 9312, Hitch Controller |
| 9313 | HITCH (Hitch Controller) | Invalid Configuration - Hitch setup for position only due to Armrest configuration | Full repair manual for code 9313, HITCH (Hitch Controller) |
| 9314 | Hitch Controller | Invalid Config - Right Draft Pin voltage is not within spec for 'no load' condition | Full repair manual for code 9314, Hitch Controller |
| 9315 | Hitch Controller (HITCH) or Armrest Controller (ARM) | Invalid Config - Left Draft Pin voltage is not within spec for 'no load' condition. | Full repair manual for code 9315, Hitch Controller (HITCH) or Armrest Controller (ARM) |
| 9316 | Hitch Controller | Invalid Config - Both Draft Pin voltages are not within spec for 'no load' condition during calibration. | Full repair manual for code 9316, Hitch Controller |
| 9317 | Hitch Controller | The Hitch Controller Calibration procedure must be performed | Full repair manual for code 9317, Hitch Controller |
| 9318 | Hitch Controller (EDC) or Armrest Controller (TMF) | Engine speed must be set above 1600 rpm during calibration of lower valve | Full repair manual for code 9318, Hitch Controller (EDC) or Armrest Controller (TMF) |
| 9319 | Hitch Controller | Invalid Config.-- Hitch calibrated for position only but Armrest calibrated for draft mode. | Full repair manual for code 9319, Hitch Controller |
| 9320 | Hitch Controller | Hitch calibration aborted due to tractor movement. | Full repair manual for code 9320, Hitch Controller |
| 9321 | Hitch Controller | Hitch calibration attempted when the engine is not running or engine speed signal is failed. | Full repair manual for code 9321, Hitch Controller |
| 9401 | IC (Instrument Cluster) | Memory Error - Double Redundant Memory - Corruption Detected And Repaired | Full repair manual for code 9401, IC (Instrument Cluster) |
| 9403 | Instrument Cluster (IC) or Universal Control Module (UCM) | Memory Error - Double Redundant Memory - Unrecoverable Memory Corruption Operable | Full repair manual for code 9403, Instrument Cluster (IC) or Universal Control Module (UCM) |
| 9404 | IC (Instrument Cluster) | Memory Error - Triple Redundant - Hour Meter Failure | Full repair manual for code 9404, IC (Instrument Cluster) |
| 9405 | IC (Instrument Cluster) | Loss Of DM1 Message From VCM | Full repair manual for code 9405, IC (Instrument Cluster) |
| 9406 | Instrument Cluster (IC) and Engine Control Unit (ECU) | No CAN Communication From VCM | Full repair manual for code 9406, Instrument Cluster (IC) and Engine Control Unit (ECU) |
| 9407 | IC (Instrument Cluster) | Memory Error - ID Errors: Unrecoverable Hardware ID | Full repair manual for code 9407, IC (Instrument Cluster) |
| 9408 | IC (Instrument Cluster) | Memory Error - Unrecoverable Panel ID | Full repair manual for code 9408, IC (Instrument Cluster) |
| 9410 | EDC | Loss Of EGR Inducement Status Message From EDC | Full repair manual for code 9410, EDC |
| 10001 | ATC (Advanced Tractor Control) | Front suspension Pump Not tank Valve solenoid is open circuit or shorted to ground | Full repair manual for code 10001, ATC (Advanced Tractor Control) |
| 10001 | Auxiliary Control Unit | Upper lockout solenoid error | Full repair manual for code 10001, Auxiliary Control Unit |
