New Holland fault codes & repair guides
All 7,052 codes· 50 per page · page 121 of 142
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| INST 7024 | INST | Reversible Fan Control open circuit or shorted to ground | Full repair manual for code INST 7024, INST |
| MFD 6001 | TCU | MFD or Front Diff Lock Solenoid Failure | Full repair manual for code MFD 6001, TCU |
| MFD 6002 | TCU (Transmission Control Unit) | Rear Diff Lock solenoid has failed | Full repair manual for code MFD 6002, TCU (Transmission Control Unit) |
| MFD 6003 | TCU (Transmission Control Unit) | Brake light relay fault | Full repair manual for code MFD 6003, TCU (Transmission Control Unit) |
| MFD 6004 | TCU (Transmission Control Unit) and Armrest Controller (ARM) | Rear Diff Lock Switch Failed in Armrest | Full repair manual for code MFD 6004, TCU (Transmission Control Unit) and Armrest Controller (ARM) |
| MFD 6005 | TCU (Tractor Control Unit / Transmission Controller) | Rear Differential Lock and Auto Differential Lock (Only CCH): 1. Diff Lock On and Auto Diff Lock switches are both active. | Full repair manual for code MFD 6005, TCU (Tractor Control Unit / Transmission Controller) |
| MFD 6006 | TCU (Tractor Control Unit / Transmission Control Unit) | CAN-BUS indicating MFD (CCH) or Front Diff Lock (4WD) Switch failed in the armrest | Full repair manual for code MFD 6006, TCU (Tractor Control Unit / Transmission Control Unit) |
| MFD 6007 | MFD/Diff Lock Controller | Both MFD and Auto MFD switches active fault | Full repair manual for code MFD 6007, MFD/Diff Lock Controller |
| MFD 6008 | MFD/Diff Lock Controller (ATC / Transmission Controller) | Steering angle sensor above maximum voltage limit | Full repair manual for code MFD 6008, MFD/Diff Lock Controller (ATC / Transmission Controller) |
| MFD 6009 | MFD / Diff Lock (Mechanical Front Drive / Differential Lock) Controller | Steering angle sensor below minimum voltage limit. | Full repair manual for code MFD 6009, MFD / Diff Lock (Mechanical Front Drive / Differential Lock) Controller |
| MFD 6010 | MFD/Diff Lock Controller | 12VS1 voltage supply is low. (possible blown fuse*) | Full repair manual for code MFD 6010, MFD/Diff Lock Controller |
| MFD 6011 | MFD/Diff Lock Controller | 12VS2 voltage supply is low. (possible blown fuse*) | Full repair manual for code MFD 6011, MFD/Diff Lock Controller |
| NH 10001 | Front Suspension Controller | Upper lockout Solenoid error | Full repair manual for code NH 10001, Front Suspension Controller |
| NH 10002 | Front Suspension Controller | Raise Solenoid error | Full repair manual for code NH 10002, Front Suspension Controller |
| NH 10003 | Front Suspension Controller | Lower Solenoid error | Full repair manual for code NH 10003, Front Suspension Controller |
| NH 10004 | Suspension Control Module | Front Axle Potentiometer above threshold | Full repair manual for code NH 10004, Suspension Control Module |
| NH 10005 | Suspension Controller | Front Axle Potentiometer below threshold | Full repair manual for code NH 10005, Suspension Controller |
| NH 10007 | Front Suspension Control Module | Go up error, Suspension Unable to return to set point | Full repair manual for code NH 10007, Front Suspension Control Module |
| NH 10008 | ATC (Armrest/Transmission/Chassis) Controller or Front Suspension Control Module | Go down error, Suspension Unable to return to set point | Full repair manual for code NH 10008, ATC (Armrest/Transmission/Chassis) Controller or Front Suspension Control Module |
| NH 10009 | Transmission Control Unit (TRANS) / Chassis Control Module | Lower lockout Solenoid Error | Full repair manual for code NH 10009, Transmission Control Unit (TRANS) / Chassis Control Module |
| NH 1002 | EDC (Electronic Draft Control) module or Hitch / Transmission control module | Radar disconnected | Full repair manual for code NH 1002, EDC (Electronic Draft Control) module or Hitch / Transmission control module |
| NH 10024 | Suspension Control Module or ICU (Instrument Cluster Unit) / Armrest Controller | Front Suspension not calibrated / 12VF1 voltage supply is low | Full repair manual for code NH 10024, Suspension Control Module or ICU (Instrument Cluster Unit) / Armrest Controller |
| NH 1003 | XCM (Multi-function Control Module) or EDC (Electronic Draft Control) | Speed sensor error | Full repair manual for code NH 1003, XCM (Multi-function Control Module) or EDC (Electronic Draft Control) |
| NH 1004 | EDC (Electronic Draft Control) module or TCU (Tractor Controller Unit) / Transmission Controller | Wheel speed sensor - signal too high | Full repair manual for code NH 1004, EDC (Electronic Draft Control) module or TCU (Tractor Controller Unit) / Transmission Controller |
| NH 1005 | Transmission Control Unit (TCU) or Electronic Draft Control (EDC) | Speed sensor signal too High | Full repair manual for code NH 1005, Transmission Control Unit (TCU) or Electronic Draft Control (EDC) |
| NH 1006 | Electronic Draft Control (EDC) module | Slip control potentiometer signal too low | Full repair manual for code NH 1006, Electronic Draft Control (EDC) module |
| NH 1007 | EDC (Electronic Draft Control) module | Slip control potentiometer signal too High | Full repair manual for code NH 1007, EDC (Electronic Draft Control) module |
| NH 1008 | Central Controller (XCM), Tractor Controller Unit (TCU), or Armrest Controller Module (ACM) / Hitch Controller | Raise / Work Switch Failure | Full repair manual for code NH 1008, Central Controller (XCM), Tractor Controller Unit (TCU), or Armrest Controller Module (ACM) / Hitch Controller |
| NH 1009 | Hitch Controller / Electronic Draft Control (EDC) module | Both external switches operated at the same time | Full repair manual for code NH 1009, Hitch Controller / Electronic Draft Control (EDC) module |
| NH 10099 | Front Suspension Controller | Front Suspension mode not enabled | Full repair manual for code NH 10099, Front Suspension Controller |
| NH 1010 | Armrest Controller, EDC (Electronic Draft Control) Module, or XCM (Multi-function Control Module) | Height limit potentiometer signal too low | Full repair manual for code NH 1010, Armrest Controller, EDC (Electronic Draft Control) Module, or XCM (Multi-function Control Module) |
| NH 1011 | TCU, EHR, or ACM | Height limit potentiometer signal too high | Full repair manual for code NH 1011, TCU, EHR, or ACM |
| NH 1012 | Hitch Controller | Drop rate potentiometer signal too low | Full repair manual for code NH 1012, Hitch Controller |
| NH 1013 | Hitch Controller (EHR - Electronic Hitch Regulation) or Armrest Controller (ARM) | Drop rate potentiometer signal too high | Full repair manual for code NH 1013, Hitch Controller (EHR - Electronic Hitch Regulation) or Armrest Controller (ARM) |
| NH 1014 | XCM (Multi-function Control Module) or EDC (Electronic Draft Control) module | R/H load sensing pin signal too low | Full repair manual for code NH 1014, XCM (Multi-function Control Module) or EDC (Electronic Draft Control) module |
| NH 1015 | XCM (Multi-function Control Module) or Hydraulic / Rear Hitch Controller | R/H load sensing pin signal too high | Full repair manual for code NH 1015, XCM (Multi-function Control Module) or Hydraulic / Rear Hitch Controller |
| NH 1016 | Electronic Draft Control (EDC) module | L/H load sensing pin signal too low | Full repair manual for code NH 1016, Electronic Draft Control (EDC) module |
| NH 1017 | XCM (Multi-function Control Module) / Hitch Controller | Left Hand (L/H) Load Sensing Pin Signal Too High | Full repair manual for code NH 1017, XCM (Multi-function Control Module) / Hitch Controller |
| NH 1018 | Electronic Draft Control (EDC) module | Both load sensing pins disconnected | Full repair manual for code NH 1018, Electronic Draft Control (EDC) module |
| NH 1019 | Hitch Controller / Hydraulic Lift Controller | Load sensing pin voltage too low | Full repair manual for code NH 1019, Hitch Controller / Hydraulic Lift Controller |
| NH 1020 | EDC (Electronic Draft Control) module | Load sensing pin voltage too high | Full repair manual for code NH 1020, EDC (Electronic Draft Control) module |
| NH 1021 | Hitch Controller | Position / draft control potentiometer too low | Full repair manual for code NH 1021, Hitch Controller |
| NH 1022 | XCM (Multi-function Control Module), EHR (Electronic Hitch Control) Module, or Armrest / Cab Control Module | Position / draft control potentiometer too high | Full repair manual for code NH 1022, XCM (Multi-function Control Module), EHR (Electronic Hitch Control) Module, or Armrest / Cab Control Module |
| NH 1023 | XCM / EDC | Control panel disconnected | Full repair manual for code NH 1023, XCM / EDC |
| NH 1024 | Electronic Draft Control (EDC) module / Hydraulic Controller (Microprocessor) | Perform Hydraulic Lift Autocalibration | Full repair manual for code NH 1024, Electronic Draft Control (EDC) module / Hydraulic Controller (Microprocessor) |
| NH 1025 | EDC (Electronic Draft Control) Module / Hitch Controller / Armrest Module (ARU) | Mouse lift lever potentiometer signal too low. | Full repair manual for code NH 1025, EDC (Electronic Draft Control) Module / Hitch Controller / Armrest Module (ARU) |
| NH 1026 | Hitch Controller / Electronic Draft Control (EDC) Module | Mouse lift lever potentiometer signal too high | Full repair manual for code NH 1026, Hitch Controller / Electronic Draft Control (EDC) Module |
| NH 1027 | Electronic Draft Control (EDC) module / Hydraulic Lift system | Maximum Lift arm position potentiometer too low | Full repair manual for code NH 1027, Electronic Draft Control (EDC) module / Hydraulic Lift system |
| NH 1028 | EDC (Electronic Draft Control) Module | Maximum Lift arm position potentiometer too high | Full repair manual for code NH 1028, EDC (Electronic Draft Control) Module |
| NH 1029 | Central Controller (XCM) or Electronic Draft Control (EDC) | Hydraulic Control valve is disconnected | Full repair manual for code NH 1029, Central Controller (XCM) or Electronic Draft Control (EDC) |
